To be able to use the full range of Shopware 6, we recommend activating Javascript in your browser.

Chain guard Ripped - AC

Chain guard Ripped - AC CB12386M / RS-1

Classicbike-Raisch Ripped aluminum chain guard suitable for the air-cooled Triumph Modern Classic models. This chain guard was not simply copied from the original like most other accessory chain guards and then slightly modified visually. It was designed to run as flat as possible over the chain and has the same line as the swingarm to look visually optimal. Because both the original chain guards as well as most of the accessories, have a lot of air upwards to the chain. Nevertheless, our chain guard is granted that this does not get contact with the chain when driving.In addition, the protection is much shorter than the original which protrudes far beyond the sprocket. This looks visually much better and more harmonious. A good splash protection is thus widely granted. The Raisch chain protectors are made of 2mm aluminum. The black chain protectors are powder coated, which ensures a deep black tone for years.

From €54.95*

Heck Weck Kit

Heck Weck Kit CB00468M / RS-1

Raisch rear wake kit for Triumph Bonneville, Thruxton & Scrambler. With this kit the bike gets a completely clean rear. Without the big original rear fender and without the original rear traffic lights made of plastic.The most minimalistic and elegant rear kit available on the market for these motorcycles! Due to the rear under fairing (aluminum lower plate) there is a good splash protection. A LED license plate light with E-number is also included. License plate holder as well as subplate are precisely laser cut from aluminum in Germany & black powder coated.It also comes with a plug that fits into the original wiring harness. That is, only turn signals, lights, etc. must be crimped and can then be connected without having to change anything in the wiring harness.All other cables, connectors, screws, etc. that are needed for installation are of course also included. Since the HeckWeck kit does NOT have a central tail light, it is mandatory to have 3in1 turn signals (these combine turn, tail & brake light in one turn signal).Further down in this description you can order the turn signals in a set and get 10% discount on the turn signals.All turn signals listed here are with E-number and street legal. If you don't want to wire and crimp the enclosed cables, plugs & insulations by yourself, you can order this service as well (you can add it to the set below). The Kit is available in 2 versions Version 1: The turn signals are mounted with a retaining plate from the inside of the strut. When the ignition is off you almost think at the motorcycle are no turn signals on it (but you see them well enough when they light up. Is not so Stvo compliant, because the turn signals are too far in the rear. Version 2: The turn signals are mounted directly on the license plate holder (turn signal holder are with the license plate holder). Legal and StvO compliant. To have the kit 100% legal, a reflector must still be attached to the license plate (you can also find it below & add it to your kit). Matching / same turn signals for front you will find at the very end of this description under the accessories.

From €169.00*

License plate holder - Shock AC

License plate holder - Shock AC CB12637 / RS0

Classicbike-Raisch Shock mount license plate holder. The simple solution for mounting the license plate on the side of the shock absorber. A side-mounted license plate gives your Triumph a completely free / clean rear end. The stainless steel base holder is simply pushed behind the shock absorber over the spike and attached together with the shock absorber. Installation is very simple and can be completed in a short time (installation instructions are included). The license plate can be individually moved inwards and outwards using slotted holes in the base holder and 4 differently positioned holes in the license plate. If the license plate is pushed all the way out, the license plate holder can be registered individually. The scope of delivery includes LED license plate lighting and all necessary mounting materials. Tips for a complete rear conversion: In order to have a completely beautifully converted rear end on your Triumph, the bulky original mudguard must of course also be removed! We offer you two options for this.Option 1: You remove the original mudguard completely and replace it with our underbody plate. (As shown in the product pictures)Option 2: You install a shorter & narrower aluminum mudguard New Indicator brackets must also be fitted if the original mudguard is removed. The accessories described can all be found under the accessory items in this product description.

€99.95*

Chain Guard Kit - Short AC

Chain Guard Kit - Short AC CB12534 / RS0

Classicbike-Raisch aluminum chain guard in the Short version - Made in Germany. The Short chain guard kits define a chain guard completely new. As minimalist as possible and running close to the chain, they provide a radical design and fulfill their most important purpose (not to get into the chain).In the chain guards is the design aspect absolute priority and not the splash protection (true to the motto: Who wants to be beautiful must suffer). A reasonably lubricated chain with modern, high-quality chain grease (such as the Motul Chain Lube) from our range but also do not splash much. In the kits, everything is included that is needed for assembly.Depending on the model, the scope of delivery still includes an additional chain guard fin, which is mounted in the middle of the swingarm to guarantee protection here as well. The Raisch chain guards are made of 3mm aluminum in Germany and then black powder coated.

€79.95*

Pantera Forkcover Springs

Pantera Forkcover Springs CB12139.1 / RS0

Colour: Silver

A pair of fork springs that work like our well-known fork covers. These are inserted between the upper and lower triple clamp. So you get the look of a classic Springer fork. That is times oldschool! For assembly, the upper triple clamp must be taken down and then the springs are simply pushed over the fork tube. Mandatory is that you have a headlight mounted, which is attached centrally and not with lamepnhaltern, which sit as original on the fork. (Suitable headlights see accessories article in this description). Note Thruxton: Who wants to mount the springs on a Thruxton, it must shorten a small piece. Dimensions: 20x6x6 cm

€120.00*

Front Number Plate Bonneville T100

Front Number Plate Bonneville T100 CB12007 / RS0

The classic among the license plates is back in our assortment. The Numbern Plate is simply screwed onto the original fender of the Triumph Bonneville T100. Holder and mounting material are included. An absolute must on every classic conversion with original long fender! The plate as well as the brackets are delivered in black powder coated. Optimally suitable to stick numbers, stickers or similar on the sign. The best looks of course an airbrush (see example photo with our Raisch logo). Included in delivery are the silver stainless steel and the brass cap nuts (see photos).

€69.95*

High Mount Front Fender/Mudguard Bracket

High Mount Front Fender/Mudguard Bracket CB11615 / RS0

The right look for every scrambler! On a reasonable Off Road Scrambler conversion, you simply need a raised front wheel fender as you know it from any Cross machine.The holder is made of stainless steel to guarantee a long durability and no breaks.Fits all air cooled Triumph models. The holder is simply mounted to the original triple clamp.We recommend either the Stripe or the Short fender from our range to match the kit (see accessories in this description).

€58.95*

Stripe front fenders AC

Stripe front fenders AC CB11216 / RS0

GFK mudguards suitable for the original mount fits Bonni, Scrambler & Thruxton. The fender has a very nice shape plus the elegant stiffeners in the middle and around the edge. The result is very high quality. Not as simple and smooth as the original one. The fender is delivered in black glossy lacquer.

€145.00*

Grand Bastart front Fender AC

Grand Bastart front Fender AC CB12137 / RS1

Triumph Colors: Raw

A large & high set handmade GRP fender made from high quality fiberglass. Made in Spain at Triumph forge Tamarit Motorcycles. The fender is attached to the upper triple clamp.The large fender protects very well from splashing dirt off-road. Visually, the fender should remind you of a classic motocross fender. Visually perfect for any scrambler look conversion with knobby tires. Available in unpainted (raw) or Jet Black (gloss black). Dimensions: 60x22x18 cm Please note, this part is a handmade fiberglass part. Such parts can never be 100% accurate and equal. That is, it may be that times a mounting hole slightly re-drilled / worked.

€159.00*

Fork covers Triumph AC

Fork covers Triumph AC CB11581.1M / RS1

A pair of fork tube covers in black powder-coated or ground and silver matt anodized, suitable for all air-cooled Triumph models (Bonneville, Thruxton & Scrambler).The cover makes the fork look much more massive (as it looks wider), which makes the fork look much better and gives it a lasting better look. In addition you get a uniform black line at the front of the bike.The original lamp holders are then of course no longer to be used. Optically the most beautiful it looks, as with the conversion on the pictures, with a 5 3/4 central headlight.For the assembly the upper fork bridge must be loosened and pulled off upward. This can be done in 30 minutes at the most.

From €69.95*

Tail Tidy Eliminator Kit

Tail Tidy Eliminator Kit CB00451 / RS1

Classicbike-Raisch rear mudguard eliminator kit for Triumph AC models Bonneville, Thruxton & Scrambler. Cool look without the big original rear wing and without the huge tail light.Consisting of a black coated aluminium plate that serves as a splash guard, an aluminium number plate holder, mounting material and installation instructions.We recommend ordering the Raisch cable set as well. This can be plugged into the original wiring harness and only needs to be connected to the turn signals / tail light. You will find the cable set under the accessories in the description. The licence plate holder fits with the 2 holes in the seat screw connection and at the same time serves as a support for the tail light & indicators. Matching tail lights can be found under the accessories below the description. We recommend the licence plate screws and a reflector as optional accessories (for those who want to be 100% legal).

€99.00*

Little Bastart front Fender AC

Little Bastart front Fender AC CB12125 / RS2

Model: Bonnie, Thruxton & Scrambler | Triumph Colors: Raw

A small, handmade GRP fender made of high quality fiberglass. Made in Spain at the Triumph forge Tamarit Motorcycles. The fender can be easily replaced with the original fender within minutes. Available in unpainted (raw) or Jet Black (gloss black). Dimensions: 36 x 15

Variants from €79.00*

€89.00*

Tamarit Belly Pan AC

Tamarit Belly Pan AC CB12128.1 / RS2

Triumph Colors: Jet Black

The Tamarit bow spoiler gives your machine, a sporty cafe racer look. From the factory, the front area of the frame is quite empty and unfilled. Since not every machine fits a classic underride protection, the sporty nose spoiler is a very nice solution. Made in Spanish handwork from high quality fiberglass material. The installation of the bow spoiler is simple and done in a short time.There is the nose spoiler in unpainted (Raw) as well as in gloss black (Jet Black). Dimensions 48x18x28 cm

Variants from €139.00*

€219.00*

The Guildford Side Covers

The Guildford Side Covers CB12133.2 / RS2

Triumph Colors: Raw | Side: Right

Handmade GRP side covers from Tamarit Motorcycles in Spain. The Guildford lids have almost the same lids as the original ones, but very nice applied ribs. The ribs are perfect for coming up with a really fancy paint design. The lids are handmade from highly finished fiberglass material, in Spain. There are the side lids in unpainted (Raw) as well as in gloss black (Jet Black). Dimensions: 23x23 cm

€99.00*

Lucas or StopHeck Kit

Lucas or StopHeck Kit CB11042M / RS2

Heck-Eliminator Kit with Lucas taillight for all air-cooled triumphs. For those who do not want to have a fender anymore but still want a classic taillight. A plug and play solution. Everything is what is needed. The taillight and a cable set which only has to be wired with the turn signals and the taillight and then fits into the original wiring harness. Only blinkers are needed, of course.

From €129.95*

License plate holder Horst adjustable

License plate holder Horst adjustable CB11406 / RS3

The license plate holder model Horst is an angle adjustable bracket for mounting on the fender. Includes license plate illumination and turn signal mount on the holder (suitable for all turn signals with M6 & M8 thread). Concentrator Holder Horst is the optimal license plate holder for anyone who wants to build a shorter fender on his motorcycle and does not want the license plate to hang down like a rat's tail on the fender. Because here the KZ is screwed directly onto the fender, through the adjustment the license plate remains recognizable even from behind. In the photo with the arrow you can see how the adjustment works. This allows the holder to be used universally for each fender rounding and length. In the photos you can see as an example, how we used the holder for the rear modification on a Bonneville. Dimensions of the license plate: width 177mm / length 165mm

€74.95*

Rear Loop LED Stripe AC

Rear Loop LED Stripe AC CB12174.2M / RS3

Rear arch / loop including clamping sleeves and LED stripe taillight and a 3D printed holder for the taillight for all air-cooled Bonneville, Thruxton & Scrambler models. In the round arch is a Ausfräsung and 3 holes on the back to insert the supplied LED strip and the holder. Detailed instructions are included. The absolute classic, but also the most elaborate and beautiful among the rear conversions! In addition to the visual aspect, the connection of the two rear frame tubes brings a significant stiffening of the entire frame, which leads to a stabilization of the driving behavior.The original rear frame is shortened according to personal preference and the round arch is also cut to the appropriate desired length. The supplied fitting sleeves are inserted into the round arch and welded (this work must be done by the customer). The other side of the fitting sleeve goes into the shortened rear frame. A thread is cut into it from below and then bolted. Of course, it can also be welded tight (work must be done by the customer). The round arch is available in 2 versions Option1: straight version Option 2: with angle. On request, a special plate can also be purchased with it, from which a seat base plate can be perfectly built. This must be done individually for each rear conversion to have a perfectly finished seat as in the photos. In the accessory articles of this description you will find a very practical metal sheet that can be welded into the round arch. The sheet facilitates the attachment of a seat and a fender. The rear round bends are not a plug&play solution. Adjustment work must be done.

From €189.95*

Rear round frame

Rear round frame CB12611M / RS3

Rear round arch including clamping sleeves for all air-cooled Triumph Modern Classic models.The absolute classic, but also the most elaborate and beautiful of the rear conversions!Beside the optical aspect the connection of the two rear frame tubes brings a clear stiffening of the entire frame, which leads to a stabilization of the driving behavior.The original rear frame is shortened according to personal wishes and the round arch is also cut to the desired length.The supplied fitting sockets are inserted into the round arch and welded (this work has to be done by the customer).The other side of the fitting sleeve is inserted into the shortened rear frame. A thread is cut in from below and then screwed in. Of course it can also be firmly welded (work must be done by the customer).The round arch is available in 2 versions Option1: straight version Option 2: with angle.The pictures say more than 1000 words. The round arch was painted black on the pictures after the adjustment (work must be done by the customer).On request, it is also possible to purchase a special plate, which can be perfectly used to build a seat base plate. This must be done individually for each rear conversion to have a perfect final seat as in the photos. In the accessories of this description you will find a very practical metal sheet that can be welded into the round arch. The sheet metal facilitates the attachment of a seat and a fender. The rear arches are not a plug&play solution. Adjustments must be made.

From €89.95*

Headlight Plate Bates

Headlight Plate Bates CB11990M / RS4

The aluminum headlight plate, in combination with a 5 3/4 inch Bates headlight, cleans the front of your bike. If you have a small 5 3/4" headlight, which is mounted centrally on the triple clamp, the small headlight gives you a fairly clear view of the steering head and all the wiring.To get a nice clean front end, there is now the aluminum headlight sheet metal (available in silver (raw aluminum), black powder coated or brushed and then clear coated). The sheet metal is simply put between the two triple clamps, behind the headlight (headlight does not have to be disassembled) and then fastened with leather straps (included in the scope of supply, optionally in black or brown) to the two fork legs (fits nicely, so that nothing rattles). An assembly instruction is naturally also included.In addition, an edge tape is included in the scope of delivery, which looks nice and classic on the one hand and protects the cables and wires on the other hand. Does not fit on motorcycles that still have a speedometer cable installed.

From €94.95*

Sideway licens plate support Swingarm AC

Sideway licens plate support Swingarm AC CB10674 / RS4

Side license plate holder including LED license plate light. Small, discreet & unobtrusive. This is what a side license plate holder should look like. Beautifully close to the wheel with a round license plate so that the license plate takes the shape of the wheel. Without expert opinion. From our experience, however, there are no problems with the green plates. Tips for a complete rear conversion: In order to have a completely beautifully converted rear end on your Triumph, the bulky original mudguard must of course also be removed! We offer you two options for this.Option 1: You remove the original mudguard completely and replace it with our underbody plate. (As shown in the product pictures)Option 2: You install a shorter & narrower aluminum mudguard New blinker brackets must also be fitted if the original mudguard is removed. The accessories described can all be found under accessories in this product description. Minimum dimensions that the license plate should have to completely cover the holder - Length: 180mm / Width: 90mm

€104.95*

Licens holder side ways AC

Licens holder side ways AC CB11091M / RS5

Lateral license plate Thruxton, Bonneville & Scrambler, attached to the strut. For all who have their license plates on the side and on the middle height of the motorcycle want to have their rear already free and clean. In the kit is the license plate with license plate illumination, a complete cable set for the wiring of turn signals, taillight and KZ luminaire, & a fitting instruction. If you do not want to crimp and solder the cable kit yourself, we also offer this as a service (see accessories in this description). Optionally you can order the kit with an underfloor plate (this serves as a splash guard if you do not want to have a mudguard installed anymore). The kit is ideally suited for mounting a taillight / turn signal combination (see accessories in this description). Alternatively, a short aluminum mudguards with classic old school taillight and chic turn signals would look (simply in the lighting category rummage). There are several points at which the turn signals can be installed in conjunction with the license plate (you can find all the suitable turn signal holders in the accessories of this description).

From €164.95*

Heavy Duty Alu side cover polished & matt

Heavy Duty Alu side cover polished & matt CB11060M / RS7

Beautiful & very high quality aluminum side cover. The covers are made of an aluminum piece (not a weld). The covers are available either in the Edellook in polished or for the rustic motorcycles in matt polished. The price is for a couple.

From €219.95*

Side cover with leather case

Side cover with leather case CB10920M / RS8

GRP side cover in the form of the original painted in black for the left side (in the direction of travel) With an intrigued leather case (genuine leather). The bag looks not only good, but is also very pratic. Eg the necessary tool for a tour fits in there (for longer tours and a little more tool you should have a bag on the right and left). The Antrahzit is an antique color, which is already easy in the correct black goes (thus a very dark Antrahzit). Antrahzit right is unlikely to be available on indefinite time, therefore currently not ordered.

From €200.00*

Aluminum side cover with leather case

Aluminum side cover with leather case CB10959.2M / RS9

Oval aluminum side cover in black powder coated. This includes a leather case (brown or black) with an integrated UK-Jack. Even without the bag, the lid looks cool. The bag can be torn or removed by means of very pratic secured pushbuttons within a few seconds. In the bag everything is necessary what you need for a tour, on-board tools & chains or other things. There is also a holder with which you can attach the bag directly to the belt.

From €230.00*

Oil filler plug - Custom Cap Flat

Oil filler plug - Custom Cap Flat CB12687 / RS10

Oil filler plug made of high-pressure cast aluminum. The screw can be easily replaced with the original one. The matching design for the Custom Cap Flat fuel filler cap.

From €38.95*

Raisch Alu Rear Fender Kit - Short

Raisch Alu Rear Fender Kit - Short CB12657M / RS10

The Alu Rear Fender Kit - Short Version is the second version of our proven Alu Rear Fender Kit. Absolute top quality at a fair price.The short version is significantly shorter, is slightly closer to the frame and has no fold on the sides. The kit thus looks less classic and fits especially well with scrambler & sporty conversions. Since almost no one likes the huge original traffic light system (tail light & turn signals), but many do not want to do without a fender, we came up with this kit. The fender is made of solid, high quality aluminum and is plug & play with brackets to screw on.In addition, the fender is already pre-drilled for the Eldorado taillight (you will find further down in the description to order) and also has a hole for the cable set (which you can also find below the description). Turn signal holder: Here are 4 different options to choose from. Where the variant with the turn signals inside the strut is not legal (but in our opinion looks the most beautiful).A turn signal holder set you can order below the description directly with it. License plate holder: Here you are again 4 versions to choose from. Central license plate holder: 1. "License plate holder - Eldorado taillight" the license plate sits on the taillight above the fender / 2. "License plate holder universal" the holder is attached below the fender to the screws for the taillight.Setiliche license plate holder: the rear kit can also be combined with a side license plate holder, which makes for a very clean and beautiful look in the rear area. Here we have one that goes on the swingarm and one that goes on the shock. Both are not approved. Other accessories: Cable set: This is needed in any case, if you do not want to cut anything off the original wiring harness. License plate screw set: Who wants to fix his license plate with matching colored screws, which can order a set with it. Reflector: Who wants to have a 100% legal rear, which must mount a reflector with. Raisch Alu Rear Fender Kit - Short

From €234.95*

Choke Knob knureld

Choke Knob knureld CB11757M / RS10

Aluminium knurled choke knob (for a particularly good grip and chic look) for all carburettors & EFI models.The choke knobs are turned from one block and then knurled afterwards.

From €23.95*

Injection Cover Ripped

Injection Cover Ripped CB11755.1M / RS10

Very high quality aluminium covers for the throttle flaps of the EFI models in ripped design. They are simply exchanged against the original ones. Available in black with contrast milling, polished or brass.

From €89.95*

Roswell Öl Screw

Roswell Öl Screw CB11973M / RS10

Oil filler plug made of high pressure cast aluminium. The screw can easily be exchanged for the original one. Can be tightened by hand or with an Allen key.Black powder coated and then hand polished to get the nice contrast between black and polished.

From €38.95*

Roswell Öl Screw

Roswell Öl Screw CB11737.2M / RS10

Oil filler plug made of high pressure cast aluminium. The screw can easily be exchanged for the original one. Can be tightened by hand or with an Allen key.Black powder coated and then hand polished to get the nice contrast between black and polished.

From €38.95*

Side Cover

Side Cover CB00475 / RS10

Styling side cover by motorcycle designer Jens von Brauck. Plug & Play. Pair left and right for painting

€229.00*

Ripped shocked Cover polished/ baclk/ silver

Ripped shocked Cover polished/ baclk/ silver CB11268.1M / RS13

Fitting to our well-known Ripped side covers, there is now also a ribbed pinion cover. It is not only ribbed, but also clearly more beautiful than the original (as you can see in the pictures). Suitable screws are included in the delivery. Made of high quality cast metal.

From €139.95*

Pinioncover CNC Silver & Black

Pinioncover CNC Silver & Black CB00452M / RS15

Pinion cover CNC milled. A true eyecatcher. Filigree and very noble at an amazing price. In alu natural or black anodised. New: Now with Schmadder protection plate (both black and silver) see first picture. Fits also for Seedmaster / America

From €94.95*

CNC Intermediate Pieces

CNC Intermediate Pieces CB10676M / RS28

Beautifully milled ALU CNC spacers in black between carburettor and injection cover and cover PAIR. These spacers can also be used without covers.

€69.90*

Conversion kit regulator

Conversion kit regulator CB00479 / RS29

This kit moves the regulator from in front of the triple clamp (where it is totally in the field of vision, and a regulator is not a very nice thing) behind the triple clamp to the place where the horn is originally located. The horn is then moved to the left under the tank. The assembly is simple (instructions and all assembly materials are included). This is absolutely safe for the regulator in terms of wind and cooling.

€59.95*

Clutch Lifter Ripped

Clutch Lifter Ripped CB12048M / RS50

Cast aluminum cover from Motone for the release lever on the clutch cover in ripped design. Available in all black, black with silver contrast or real brass. The part is simply put over the lever and fixed with a grub screw.

From €29.95*

Motone Chain Guard Tanto AC

Motone Chain Guard Tanto AC CB12027M / RS200

A very nice and slim chain guard, made of high quality stainless steel.Fits to all air cooled Triumph models. The chain guard can be easily replaced with the original one in a few minutes.

From €58.95*

Tamarit stainless steel chain guard AC

Tamarit stainless steel chain guard AC CB12366 / RS600

Tamarit Motorcycles chain guard for the air cooled Triumph models. All Tamarit chain guards are made of stainless steel. This provides a very nice silver finish as well as rust protection.The covers provide by their ribbed design for a sporty elegant look. The attachment is very simple and done in a short time. Original chain guard off and attach the new just as again. On request, we can also provide the chain guard in black powder coated lifern.

€99.00*

Start license plate for SLC holder

Start license plate for SLC holder CB12049M / RS600

SW-Motech start number plate suitable for all Sw-Motech Legend Gear SLC bag holders (matching holders see ZUbehörartikel in this description). The plate is made of brushed aluminum and looks very high quality. On request, we can also coat this black powder for an additional charge. The sign is very easy, just like the Legend Gear bags with the quick release system clicked into SLC holder. Perfectly suited for all who have installed the SLC holder and do not always want to have the bag on the bike but do not want to look at the holder.

From €55.00*

Rizoma Öl Einfüllschraube Triumph

Rizoma Öl Einfüllschraube Triumph CB11918M / RS600

Öl Einfüllschraube von Rizoma, für alle Triumph Modelle. Für alle die es besonders Edel mögen, ist die Schraube von Rizoma genau das richtige.Denn alle Rizoma Produkte werden aus sehr hochwertigem Aluminium hergestellt und haben eine sehr schöne, eloxierte Oberfläche. Die Schraube wird ganz einfach gehen die originale ausgetauscht.

From €50.50*

Öl Einfüllschraube Crown

Öl Einfüllschraube Crown CB11834 / RS600

Hochwertige, CNC gefräste Alu Schraube in tief schwarz eloxiert. Einfach gegen die originale Schraube austauschen.

€24.95*

Universal license plate holder

Universal license plate holder CB11294M / RS600

Universal identification holder for mudguards. The license plate is universal for many mudguards. It is screwed from the inside to the fender (see photo)

From €29.95*

Ripped Side Cover painted

Ripped Side Cover painted CB11102M / RS600

A pair of high quality ABS plastic side covers in ripped style in gloss or matt black lacquered. Due to the 3 slotted ribs the side covers look really classic and sporty.A nice little side effect is that the motorcycle also gets a little more air.The lids are ready painted. Behind the slots there is a fine silver mesh aluminium grid glued in, so you can't just look through the ribs (if you want a grid with coarse meshes, like the white and silver covers, you have to make it yourself).Who wants to repaint the covers in his motorcycle color, can contact us, because we also have the covers in unpainted.For Scramblers: The cover can also be ordered for the left side only (click on Ripped side cover Scrambler below in the accessories of this description)

From €235.95*

Heavy Duty Alu Rear Fender

Heavy Duty Alu Rear Fender CB11063.1 / RS600

Design: Brushed

Ein schön kurzer Alu-Kotflügel der Plug&Play anzubauen ist. Passt an alle Bonneville, Scrambler und Thruxton Modelle. Der Kotflügel ist aus sehr hochwertigem massiven Alu (wahlweise in poliert oder matt gebürstet). Er ist etwas breiter als der B-PP-A Au Kotflügel, den wir auch anbieten. Also perfekt geeignet für alle, die einen etwas breiteren Hinterradreifen (140, 150 oder 160) fahren. Ausserdem hängt er etwas tiefer als der originale, um eine flachere Linie zu bekommen (weniger Luft zwischen Kotflügel und Reifen).

€219.95*

Heavy Duty Alu Mudguard

Heavy Duty Alu Mudguard CB11040M / RS600

Aluminum mudguards in the Heavy Duty Style For all models with spoked wheels. What does that mean ? This mudguard is made of solid solid (made of 3mm thick aluminum). These mudguards feel really high quality and at the price. The mudguard is simply screwed onto the original bracket (no other accessory or holder is required).

From €159.95*

Heavy Duty Bobber Aluminum Mudguard

Heavy Duty Bobber Aluminum Mudguard CB11041M / RS600

Alu Bobber fender in heavy duty short style For all models with spoked wheels. What does that mean ? This mudguard is made of solid solid (made of 3mm thick aluminum). These mudguards feel really high quality and at the price. The mudguard is simply screwed onto the original bracket (no other accessory or holder is required).

From €149.95*

CNC oil filler cap

CNC oil filler cap CB10814M / RS600

CNC milled aluminum oil filler cap with laser-engraved logo and vertical knurling for easy removal.

From €23.00*

JvB Seat & Tail Tidy combination

JvB Seat & Tail Tidy combination CB10706M / RS600

Seat and fender combination. This beautiful Flat Track of the company JVB, gives your machine a whole new Loook! Perfect fit for Scrambler, Flat Track and Bobber conversions. Gives the tail in conjunction with the seat of the machine a nice flat line. The tail is available in two versions (please choose). Version1: The kit can be plug & play to an original motorcycle. Version2: The tail is shorter and the rear frame of the machine must be shortened / cut off. This is of course more effort, but also looks very good when the tail is a bit shorter. Matching license plate holder & license plate light holder can be found in the accessories of this description. The tail light is included.

From €819.00*

Aluminum fenders

Aluminum fenders CB00453M / RS600

Aluminum front fender for 17 inch wheel tags. Handmade and polished. With a really very shapely holder. Easy to paint when a different color is desired. Must be adapted ! Also suitable for Triumph with 17 cast wheel, please select model.

From €190.00*

Front fender Bobber

Front fender Bobber CB00474 / RS600

Styling front fender from motorcycle designer Jens von Brauck. Nice and tight and in a perfect quality. This GRP part is not laminated but pressed. This results in a nice smooth surface. Plug & Play. Ready for painting. The fender is the shortest we have in the porgram and gives the front a very cool look, because you can see quite a bit of the tire but still has a fancy fender on it.In addition, the fender lies nice and flat over the tire.

€149.00*

JVB Headlight Kit

JVB Headlight Kit CB00476 / RS600

Styling lamp mask including headlight from JVB. Absolutely new and distinctive look. Ready for painting.The mask changes the look of the machine considerably. Because of the no longer protruding headlight the bike looks more modern (pictures say more than words). Not a Plag&Play solution. A little rebuilding is required. Horn and regulator have to be moved. Don't worry, this can be done without too much effort.

€349.00*

Aluminum side cover

Aluminum side cover CB00440.2M / RS600

Black anodised aluminium side cover. THRUXTON + BONNIE. Sporty look in the style of number plates from racing. Slimmer than the original lids and we think they fit perfectly with the Thruxton. Easy to paint if a different colour is desired. PAAR.Can also only be ordered for the left side for scramblers.

From €149.00*

Body parts for your air-cooled Triumph Modern Classic motorcycle up to 2015 – Customise your motorcycle

With the right body parts, such as covers, emblems, rear ends or conversion kits for rear ends, license plate holders, mudguards and side panels, you can customise the design of your bike while also protecting important components. At Classicbike Raisch, you'll find high-quality parts that have been specially developed for our Bonneville, Thruxton and Scrambler models, as carburettor or fuel-injected (EFI) versions, and offer a perfect fit. Invest in high-quality body parts to not only give your bike a unique look, but also to ensure optimal functionality and durability.