Classicbike-Raisch short license plate holder for Triumph for Speed 400 / Scrambler 400 X made of 3mm stainless steel and black powder coated.Made in Germany & Stvo compliant (legal).ATTENTION: The set is without blinker holder, these must be ordered separately (see accessories in this description). The perfect and most minimalistic license plate for the Triumph 400 models available on the aftermarket. The holder also has a well thought-out system that allows you to adjust the license plate angle steplessly, as well as the turn signal distance steplessly to the respective arm length of your turn signals.We have designed the license plate holder to be extra small so that it can be used in any country in the world.Dimensions of the license plate holder (height x width): 100mm x 160mm   The holder replaces the ugly and much too long original plastic license plate holder and the original license plate light with a high-quality LED version. Included in delivery: - Mounting material- License plate holder- LED license plate light - Detailed step-by-step installation instructions   The license plate light disappears deep under the original rear light of your 400 and is therefore barely visible. This allows the license plate to disappear deep into the rear and gives the motorcycle a really clean look.The vario blinker holders (which we recommend ordering as well) are attached directly to the license plate holder and can be slid inwards and outwards continuously.This allows the indicators to sit discreetly to the left & right of the license plate. The prescribed minimum distance is maintained with all indicators.The original Triumph indicators can NOT be reused.Classicbike-Raisch tip for replacing indicators: Under the accessories in this product description, you will find suitable blinker plugs to connect accessory indicators directly to the original wiring harness. No ABE, certificate or similar is required for our short license plate holder. It complies with the StvO & does not have to be registered. In other words, simply install it and you are still legally on the road.  To ride completely legally, a reflector must of course be fitted again. You can find a suitable reflector among the accessories in this description.  We also offer an optional license plate screw set (see accessories) so that the annoying license plate can be fitted as discreetly as possible. We have taken great care in the design to ensure that the holder does not come into contact with the rear wheel even at maximum deflection, which is not the case with all holders on the market.

Short licence plate holder for Triumph Street Twin / Cup / Scrambler - Speed Twin 900 / Scrambler 900 made of 3mm stainless steel and black powder coated.ATTENTION: The set is without indicator holder, these must be ordered separately (see accessories in this description). The perfect and most minimalist licence plate for the original mudguard of your Triumph.We have made the licence plate holder extra small in the new version so that the licence plate holder can be used for any country in the world.Dimensions (height x width): 100mm x 160mm The licence plate holder does not have indicator brackets. These must be ordered separately (see accessories in this description). There are three different indicator holders to choose from: 1: The vario indicator holder. These can be adjusted in width to ensure the correct spacing for each licence plate with each indicator.2: The 3-1 indicator/rear light combination kit is installed. The original rear light is replaced by indicators with integrated rear and brake lights. (this variant is only available for Street Twin / Speed Twin 900) The holder replaces the ugly and much too long original plastic licence plate holder and the licence plate light. Scope of delivery: - Mounting material- Licence plate holder- LED licence plate light - Detailed step-by-step fitting instructions     The license plate light disappears deep into the fender and is barely visible. This brings the license plate nice and close to the mudguard.The vario blinker holders (which we recommend ordering as well) are attached directly to the license plate holder and can be moved inwards and outwards.This allows the indicators to sit discreetly to the left & right of the license plate. The prescribed minimum distance is maintained with all indicators.The original Triumph indicators can NOT be reused. No ABE, certificate or similar is required for our short licence plate holder. It complies with the StvO & does not have to be registered. In other words, simply install it and you are still legally on the road. To ride completely legally, a reflector must of course be fitted again. You can either use the original one (which we do not recommend as it is very large) or you can order the small reflector from our range (see accessories in this description).We also offer an optional licence plate screw set (see accessories article) so that the annoying licence plate can be fitted as discreetly as possible.When designing the bracket, we have taken great care to ensure that it does not come into contact with the rear wheel even at maximum deflection, which is not the case with all brackets on the market.

Short license plate holder for Triumph Scrambler 1200 XC & XE made of 3mm stainless steel and black powder coated.ATTENTION! The set is without turn signal holder, these must be ordered separately (see accessory items in this description). The perfect and most minimalistic license plate for the original aluminum fender of the Triumph Scrambler 1200.We have made the license plate holder extra small for the new version, so that the license plate holder can be used for any country in the world.Dimension (height x width): 100mm x 160mm The license plate holder does not have turn signal holders. This must be ordered separately (see accessory items in this description). There are 3 different turn signal holders to choose from: 1: The vario turn signal holder. These can be adjusted in width to ensure the appropriate distance for each license plate with each turn signal.2: Turn signal adapter - Scrambler 1200: These are attached to the frame and not to the license plate holder.3: The 3-1 turn signal/tail light combination kit is installed. The original tail light is replaced by turn signals with integrated tail and brake light. The holder replaces the ugly and much too long, original plastic license plate holder as well as the license plate light.Mounting hardware, license plate holder, LED license plate light and detailed step by step mounting instructions are included. Classicbike-Raisch tip:If you want to build a really nice rear end with the original mudguard on your Scrambler, we recommend ordering our Plug & Play LED rear light (can be seen in some product photos).You can find the rear light under accessories in this product description. The original plastic holder is partially preserved. It must be trimmed a little to be able to mount ours. Is quite simple and also described in the instructions (who wants to look before whether he trusts himself, can download the instructions under Downloads in this description as a PDF).If you want to upgrade the bike back to the original holder, you need the plastic license plate holder new (we also offer as a spare part, see accessories in this description). The license plate light disappears nice and deep in the fender and is hardly visible. So the license plate moves nice and close to the fender.Turn signal holder are integrated directly on the license plate holder. Thus, the turn signals sit nicely discreet left & right next to the license plate. With all turn signals the prescribed minimum distance is maintained.The original Triumph turn signals can NOT be used. For our short license plate holder is no ABE, certificate or similar necessary. It complies with the StvO & does not need to be registered. Say simply install and you are still legally on the road. To drive completely legally, of course, a reflector must be installed again. For this you can either take the original (which we do not recommend, because this is very large) or you order the small reflector from our range in addition (see accessories in this description).To mount the annoying license plate as discreetly as possible, we offer an optional license plate screw set (see accessory article).In the design we have paid meticulous attention to the fact that the holder does not get contact with the rear wheel even at maximum compression, which is not given with all holders on the market. 

Short number plate holder for Triumph Speed Twin 1200 made of stainless steel and black powder coated. The perfect and most minimalist number plate for the original aluminium mudguard of the Speed Twin. We have made the licence plate holder extra small for the new version, so that the licence plate holder can be used for any country in the world.Dimension (height x width): 100mm x 160mmWe now also offer additional Vario indicator holders that can be mounted on the licence plate holder (optional / you will find the holders under the accessories in this description). The holder replaces the ugly and much too long original plastic licence plate holder.Mounting material, licence plate holders and detailed step-by-step mounting instructions are included. If you want to make your tail even cleaner, you can replace the original tail light with 3-1 turn signals / tail light combination turn signals. To do this, you need the "Triumph tail light replacement for 3-1 turn signals" kit (see accessories article). The number plate light disappears nice and deep into the mudguard and is hardly visible. This way the number plate moves nice and close to the mudguard. No ABE, certificate or similar is required for our short licence plate holder. It complies with the StvO and does not need to be registered. Simply install it and you can continue to ride legally. In order to ride completely legally, a reflector must of course be installed. You can either use the original one (which we do not recommend, as it is very large) or you can order the small reflector from our range (see accessories in this description).To mount the annoying number plate as discreetly as possible, we offer an optional number plate screw set (see accessory article).We have taken great care in the design to ensure that the holder does not come into contact with the rear wheel even at maximum compression, which is not the case with all holders on the market.

The license plate holder model Horst is an angle adjustable bracket for mounting on the fender. Includes license plate illumination and turn signal mount on the holder (suitable for all turn signals with M6 & M8 thread). Concentrator Holder Horst is the optimal license plate holder for anyone who wants to build a shorter fender on his motorcycle and does not want the license plate to hang down like a rat's tail on the fender. Because here the KZ is screwed directly onto the fender, through the adjustment the license plate remains recognizable even from behind. In the photo with the arrow you can see how the adjustment works. This allows the holder to be used universally for each fender rounding and length. In the photos you can see as an example, how we used the holder for the rear modification on a Bonneville. Dimensions of the license plate: width 177mm / length 165mm

The Rizoma license plate holder "FOX" with license plate illumination has been the absolute classic in the motorcycle industry for years and convinces without many words by its sophisticated adjustment system and perfectly matured construction. The original aluminium mudguard of the Triumph Speed Twin is preserved. The original very long license plate holder is replaced by the short Rizoma holder. A removable reflector is included in the delivery. The rear looks perfect in combination with small Rizoma turn signals, which can be mounted on the original mounting, best together with our turn signal adapters. If the Rizoma Fox tail is too expensive, we recommend our simple but minimalistic Raisch holder (see similar products).

Universal identification holder for mudguards. The license plate is universal for many mudguards. It is screwed from the inside to the fender (see photo)