Steel Front Fender Bobber
CB11413M
/ RS2
From
€329.00*
Metal front fender for the bobbers.Can be exchanged Plug&Play. Can be painted if necessary or simply installed in the Steel look (but must then be painted with clear varnish and powder coated, otherwise the steel will rust). Harmonizes perfectly with the Steel-look rear fender kit (see accessories in this description).The fender is available in 3 versions.Variant 1: Raw untreated steelVariant 2: Black silk matt powder coated (similar surface as most motorcycle frames)Variant 3: Black high gloss powder coated. This coating comes, by the extremely high-quality powder that is used, a black shining lacquering really very close (see photos)!But you can't expect a 110% perfect surface like from a painter who primes and grinds the fender beforehand.Since the fender is made of handmade stainless steel, it has a structure and slight unevenness (which you can easily see after powdering). If you want it perfect or in a different colour, you have to prime the fender and then have it painted. But we would still recommend to powder the fender in advance, because this is the perfect rust protection (but then variant 2 black matt is sufficient).If you would like to have the mudguard powder-coated in black (silk matt), you can order the product "Surcharge mudguard black" in the accessories of this description. Since the fender is made of handmade stainless steel, it has a structure and slight unevenness (which can be easily seen after powder coating). If you want it to be perfect you have to prime the fender and then have it painted. However, we would still recommend to have the fender powdered beforehand, as this serves as perfect rust protection.The black detail photos show the rear bobber fender and serve only to illustrate the colour tone.
Rizoma Alu Rear Mudguard BL & SI
CB11264M
/ RS2
€235.00*
Aluminum mudguards for Bonneville and StreetTwin models.
Fitting to the front wheel fender, Rizoma also has a rear wheel fender in the same aluminum finish.
The mudguard is supplied with plug and play with mounting brackets and screws. Holes for the taillight must be set individually. We recommend the rear lights which can be found in the accessories of this description,
The license plate must be attached to the side of the wing or an additional license plate must be fitted.
Stripe front fenders AC
CB11217
/ RS2
€144.99*
GFK mudguards suitable for the original bracket fits on Bonneville T100 + T120 & all Street models.
The fender has a very nice shape plus the elegant stiffeners in the middle and around the edge. The result is very high quality. Not as simple and smooth as the original one. The fender is delivered in black glossy lacquer.
Alu side cover Street & Bonneville
CB11505M
/ RS2
From
€240.00*
Aluminium side lid with integrated real leather bag in brown, suitable for Bonneville T100 & T120 as well as StreetTwin, Cup & Scrambler.On the one hand, the side covers are much nicer than the original ones, because they are simply much smaller, and on the other hand, the leather bag looks great and is also practical.Can simply be exchanged one to one with the original ones (are changed in a few seconds).The lids are sold separately.
Alu side cover
CB11213M
/ RS2
From
€154.95*
Handcrafted aluminium side covers Made in Italy, for Bonneville T100 & T120 as well as StreetTwin, Cup & Scrambler.Attention fits on the Street Scrambler only on the left side.The lids give both the Bonneville and all Street Twin models a much nicer side view. The covers are much smaller than the original ones and disappear in the frame triangle, making the frame tubes visible.Replacing them takes only a few seconds (the lids are simply plugged in as well as the original ones).The aluminium covers are available in a matt satin silver or black powder coated finish. They are also available individually for left & right or as a pair (cheaper).
Licensplate Holder site ways CNC
CB11182M
/ RS2
From
€349.00*
This is how it should look on a real bobber! On a bobber, the license plate simply belongs on the side and not on the fender.
The side license plate holder from Wunderkind also fits the Triumph Bonneville T100 / T120 - Street Twin / Scrambler / Cup - Scrambler 900 - Speed Twin 900
The holder is very elegantly CNC-milled and black anodized. There is an optional holder for all those who want to continue using the original rear light of their Bobber & a reflector fits on the Kz holder (see accessories in this description).
Details at a glance+ Laterally mountable license plate holder+ 3-stage width adjustment of the plate (towards or away from the wheel) + Possibility to tilt the plate by 30+ Integrated LED lighting + License plate can be inserted into the frame from above + Concealed cable routing + Surface finish with BLACKPearl anodized + CNC-milled aluminium+ Design: WUNDERKIND-Custom
The bracket is supplied with a parts certificate for the Triumph Bobber & Speedmaster.For all other models (Bonneville / Street / Scrambler / Speed) it must be registered individually (which is not a problem due to the existing parts certificate).ATTENTION for Bonneville models: On these models, the NCIHT holder fits together with the original exhaust.
The license plate is optionally available for German (standard and 200x220 size), Austrian, Swiss and French license plates.
Licens holder side ways LC
CB11092M
/ RS2
From
€164.95*
Thruxton Thruxton, BonnevilleT120 + T100, and all StreetTwin models (does not fit with Thruxton R if the original struts are installed) attached to the strut. For all who have their license plates on the side and on the middle height of the motorcycle want to have their rear already free and clean. In the kit is the license plate with license plate illumination, a complete cable set for the wiring of turn signals, taillight and KZ luminaire, & a fitting instruction. If you do not want to crimp and solder the cable kit yourself, we also offer this as a service (see accessories in this description).
Optionally, the kit can be ordered with a base plate (this is used as a splash guard if you do not want to have a fender installed anymore).
The kit is ideally suited for mounting a taillight / turn signal combination (see accessories in this description). Alternatively, a short aluminum mudguards with classic old school taillight and chic turn signals would look (simply in the lighting category rummage).
There are several points at which the turn signals can be installed in conjunction with the license plate (you can find all the suitable turn signal holders in the accessories of this description).
Tamarit Fork Protectors Scrambler 1200
CB12216.4
/ RS3
€210.00*
Triumph Colors:
Matt Khaki Green
A pair of handmade fiberglass fork protectors in motocross design.
An absolute must have on any real off road & scrambler machine. The original protectors in the rough plastic surface just look cheap compared to these Tamarit protectors.
There are the protectors optionally in unpainted (Raw) as well as in all Triumph original colors. The most common Triumph colors as well as the unpainted parts we actually always have in stock. A color that we do not have in stock will take about 2-6 weeks to be available.
Please note, this part is a handmade fiberglass part. Such parts can never be 100% true to size and it may happen that a hole may need to be minimally drilled / re-drilled.
Variants from €120.00*
License plate holder Horst adjustable
CB11406
/ RS3
€74.95*
The license plate holder model Horst is an angle adjustable bracket for mounting on the fender. Includes license plate illumination and turn signal mount on the holder (suitable for all turn signals with M6 & M8 thread). Concentrator Holder Horst is the optimal license plate holder for anyone who wants to build a shorter fender on his motorcycle and does not want the license plate to hang down like a rat's tail on the fender. Because here the KZ is screwed directly onto the fender, through the adjustment the license plate remains recognizable even from behind.
In the photo with the arrow you can see how the adjustment works. This allows the holder to be used universally for each fender rounding and length.
In the photos you can see as an example, how we used the holder for the rear modification on a Bonneville.
Dimensions of the license plate: width 177mm / length 165mm
Heavy Duty Rear Fender LC
CB11293M
/ RS3
From
€224.95*
This Alu Rear Fender for Bonneville and Street models.
The Fender is made of thick, high-quality aluminum and can be screwed on to Bonneville T100 + T120 and all street models. It replaces the chunky and long original fender.
Turn signal holders, license plate, taillights and turn signals must be ordered seperatly. Or order her the Raisch Alu Fender Kit.
The mudguard can also be ordered in black coated. For this, please order under accessories the supplemental license extra black mudguard (extra charge: 30 €)
Rear Loop LED Stripe LC
CB12173.2M
/ RS3
From
€189.95*
Rear arch / loop including clamping sleeves and LED stripe taillight and a 3D printed holder for the taillight for all water-cooled Bonneville & Street models.
In the round arch is a milled out and 3 holes on the back to insert the supplied LED strip and the holder. Detailed instructions are included.
The absolute classic, but also the most elaborate and beautiful among the rear conversions! In addition to the visual aspect, the connection of the two rear frame tubes brings a significant stiffening of the entire frame, which leads to a stabilization of the driving behavior.The original rear frame is shortened according to personal preference and the round arch is also cut to the appropriate desired length. The supplied fitting sleeves are inserted into the round arch and welded (this work must be done by the customer). The other side of the fitting sleeve goes into the shortened rear frame. A thread is cut into it from below and then bolted. Of course, it can also be welded tight (work must be done by the customer).
The round arch is available in 2 versions Option1: straight version Option 2: with angle.
On request, a special plate can also be purchased with it, from which a seat base plate can be perfectly built. This must be done individually for each rear conversion to have a perfectly finished seat as in the photos.
In the accessory articles of this description you will find a very practical metal sheet that can be welded into the round arch. The sheet facilitates the attachment of a seat and a fender.
The rear round bends are not a plug&play solution. Adjustment work must be done.
Rear round frame
CB12542M
/ RS3
From
€89.95*
Rear round arch including clamping sleeves for all air-cooled Triumph Modern Classic models.The absolute classic, but also the most elaborate and beautiful of the rear conversions!Beside the optical aspect the connection of the two rear frame tubes brings a clear stiffening of the entire frame, which leads to a stabilization of the driving behavior.The original rear frame is shortened according to personal wishes and the round arch is also cut to the desired length.The supplied fitting sockets are inserted into the round arch and welded (this work has to be done by the customer).The other side of the fitting sleeve is inserted into the shortened rear frame. A thread is cut in from below and then screwed in. Of course it can also be firmly welded (work must be done by the customer).The round arch is available in 2 versions Option1: straight version Option 2: with angle.The pictures say more than 1000 words. The round arch was painted black on the pictures after the adjustment (work must be done by the customer).On request, it is also possible to purchase a special plate, which can be perfectly used to build a seat base plate. This must be done individually for each rear conversion to have a perfect final seat as in the photos.
In the accessories of this description you will find a very practical metal sheet that can be welded into the round arch. The sheet metal facilitates the attachment of a seat and a fender.
The rear arches are not a plug&play solution. Adjustments must be made.
Race Bobber - Light conversion
CB12646
/ RS4
€5,995.00*
Classicbike-Raisch Race Bobber Light complete conversions including TÜV registration.
These are Triumph Bobber bikes that we convert to 17" rims and sports tires. Visually, the bobber becomes a completely different motorcycle and a real eye-catcher! From a technical point of view, a lot has also changed, because the Bobber rides much better and very agile with the sport tires! With the tires, the Bobber really invites you to take corners (as far as the lean angle allows).
We regularly receive inquiries from customers who would like to have a Race Bobber but already have a motorcycle or don't want to spend €26,000 or more on a new bike. We now offer you the Race Bobber Light kit. What does that mean? The kit means that you bring your bobber to our workshop and get all the conversions done that were done on the chrome bobber in the product pictures. The price also includes the TÜV registration of the necessary parts. The registration makes the conversion StvO-compliant and legal to ride on German roads.
The kit includes
- Conversion to the 17" rims (front + rear) - Supersport tires (front + rear) - 2x Wave brake disk front - 1x Wave brake disk rear- Wunderkind steel rear mudguard including 3-1 indicators / rear light (in black powder-coated - can also be painted for an extra charge)- Wunderkind side license plate holder- Race Bobber front wheel mudguard (painted in desired color)- Raisch short chain guard - All workshop work- TÜV registration
Further accessories
Of course, there are virtually no limits to your Race Bobber at our company. You can also order other individual conversions (take a look at our other Race Bobber conversions for inspiration).Here is a small selection of other options that are still possible:
- Exhaust system (Raisch recommendation: Side Pipe) - Speedometer conversion to a small Motogadget speedometer- Brake system - Various add-on parts with black powder coating- Seat - Various covers - Front indicators- Handlebar conversion including handlebar end indicators & Motogadget underbar mirror - Individual painting according to customer requirements- And much more, for more inspiration & ideas, have a look at our other Race Bobber conversions or contact us
The base
Don't have a bobber yet? No problem! We will be happy to find a suitable base for you.
Side license plate holder - rear wheel
CB12774
/ RS5
€239.90*
The side license plate holder from Motone is a legal and registration-free option for mounting your license plate on a side license plate holder centered behind the rear wheel. A very practical solution for motorcycles that have a very short rear end and can't find a good place to mount the license plate and the turn signals or 3-1 turn signal / rear light combination. In addition to the license plate holder, you can also order turn signal holders (see accessories below this description). With this solution, you can easily get your lighting and license plate in a legal position (no entry in the TÜV required).
This is a very good solution for bobber conversions with a short fender.
A small LED license plate light (street legal with E-number) is included with the license plate holder.
This is equipped with a long cable to be able to lead it along the swing arm to the motorcycle's wiring harness.
Alu Mudguard Thruxton / Speed Twin
CB11530M
/ RS5
From
€134.95*
This aluminum front fender replaces the simple plastic fender on the Thruxton 1200 & Speed Twin (plug & play replacement). The surface of the mudguard is beautifully polished, which looks really good on any cafe racer.
The Speed Twin already has an aluminum mudguard fitted ex works. However, this one still looks good, as it is narrower and therefore more of the tire is visible. This makes the tire look sportier.
The fender is optionally available in polished or black (silk matt) powder-coated. Also ideal for painting (see photos of the blue Thruxton). It is best to talk to your trusted painter beforehand to find out whether he would like the fender in polished aluminum or better coated in black (as the coating is a bit like a primer).On request, we can add a piece of sanding fleece free of charge so that you can brush the polished mudguard to a matt finish by hand (see photo).
Ripped Cover Brass Style
CB12298M
/ RS5
From
€74.95*
Ripped cover made of real brass for the left + right engine cover.
The covers can be replaced in no time with 2 screws.
The nice thing about the polished real brass is that brass gets a little pattina with time and becomes more and more beautiful.
Smart Heck for StreeT & Bonneville
CB10904M
/ RS5
From
€239.95*
A nice crisp and short tail all Street & Bonneville LC models
Perfect for all those who find the original fender and the Kz mount too big and bulky, but still want a bit of fender. The kit comes with all brackets, mounting hardware and rear light. The fender is made of black GFK unpainted.
Attention: Does NOT fit the Bonneville with the original seat. A flat StreetTwin seat or e.g. the Cool Seat from our program must be mounted.
The turn signals can be mounted simply as in the photos on the fender (for this a hole must be drilled into the fender) or one mounts them with the help of an extra holder on the number plate (see accessories in this description).
Fork feets Thruxton 1200 R / RS black painting
CB11965
/ RS9
€199.00*
If you don't like the original silver fork feet on your thruxton, you can simply have it coated black by us. Just send the disassembled fork to us and you will get it back with black fork feet. If you can't do the disassembling yourself, you can also send the whole fork to us and we will do it for you (extra charge).
It takes about 2 - 3 weeks until you get the part back.
By default we always make the parts in black satin. Several other colors are of course also possible on request.
The price is for the coating of both fork feet. Looks especially good in combination with black fork tubes.
Frame Plate Milled - Bobber
CB12810
/ RS10
€109.95*
Frame Plate Milled - suitable for all Triumph Bobber models.
Give your Bobber a classy detail!This CNC-milled aluminum plate replaces the simple original plate and makes your motorcycle more valuable. Almost everyone who loves their motorcycle is also in love with details, and it is precisely in small eye-catchers like the frame plate that the details of a high-end bike lie.
Elegant design: The design of the frame plate subtly picks up on the Union Jack flag - a stylish statement that emphasizes the British origin of your bike.
High-quality workmanship: Made from robust aluminium and anodized in deep black, the plate offers a first-class look and long durability.
Attention to detail: After anodizing, our Raisch logo is finely and precisely engraved - a real eye-catcher that makes your bike unique.
Easy installation:Replacing the plate is as simple as it is ingenious: the conversion is completed within a minute - without any special tools.
Included in the scope of delivery:For the perfect look, we supply high-quality bolts with black powder-coated heads. Everything fits seamlessly into the design of the black frame plate.
High Bunker Street Scrambler mudguard
CB12804
/ RS10
From
€239.00*
High / top-mounted fiberglass-reinforced plastic of the highest quality for Triumph Street Scrambler / Scrambler 900
Fits from FIN 914448.
On a scrambler, it is simply a MUST to mount the fender at the top (under the fork bridge). This is the only way to give the motorcycle the off-road look it needs to look really cool! The Bunker custom fender is of very high quality and can be ordered in either glossy black or matte. The paintwork on the fender is truly top notch!
Installing the fender is very easy and quick.Everything needed for installation is included in the scope of delivery.We recommend you use this mudguard instead of the Triumph accessory mudguard, as it has a slightly more attractive shape and is of at least the same high quality.
RxV headlight kit - Bobber
CB12789
/ RS10
From
€579.00*
RxV “Raisch x Vagabund” headlight fairing incl. LED spotlight for Triumph Bobber – turn your Bobber into a real head-turner!
If you want to give your Triumph Bobber a completely new and exclusive look, there is no way around the RxV headlight fairing including LED headlights. This unmistakable design piece was developed by the renowned motorcycle design company Vagabund Moto in collaboration with Classicbike-Raisch – and the result is more than just another component: it is a real statement.
The RxV headlight kit is the centerpiece of our exclusive RxV Bobber project, which was developed in collaboration with Vagabund Moto. This special Bobber has attracted a lot of attention due to its design elements such as the striking headlight fairing and the unique rear conversion. Both components, the headlight mask and the RxV rear end, are available to buy exclusively from Classicbike-Raisch – so you can give your own Triumph Bobber the unmistakable RxV look.
Your Bobber, redefined:
Exclusive design from Vagabund Moto: the perfectly designed headlight fairing gives your Bobber a sophisticated and modern look It is a highlight for anyone who wants to stand out from the crowd with their bobber.
Complemented by the RxV rear: The completely redesigned rear end, which you can also find exclusively from us, rounds off the overall design. This design duo – headlight and rear – transforms your Triumph Bobber into a real custom bike.
Premium materials and perfect fit: Each part has been 3D printed with the highest precision to seamlessly fit your Bobber and ensure easy installation.
Paintwork: The headlight mask is available either in RAW (unpainted) or in gloss/matt black (the painted parts are made to order and have a rough delivery time of 4-8 weeks
Easy installation – all materials included:The headlight kit comes with all the necessary brackets and mounting materials.For bobber models with a standard LED headlight, we recommend the optional cable set for a plug-and-play installation without any cutting or soldering. You can find this add-on in the accessories section of our shop.
Optics tip from Classicbike-Raisch:Do you want to perfect the clean look of your bobber? Combine the RxV lamp mask with a smallMotogadget speedometer that makes the front of your bobber look even more minimalist and elegant. Of course, you can also find this high-quality speedometer in our shop!
RxV Rear Kit - Bobber
CB12790
/ RS10
From
€929.00*
RxV rear kit for Triumph Bobber – exclusive at Classicbike-Raisch
The RxV rear kit stands for the highest design excellence and was developed in close collaboration between Classicbike-Raisch and the renowned motorcycle design company Vagabund Moto. Two years ago, the extraordinary RxV Bobber was created from this collaboration, which caused a worldwide sensation with its unmistakable look. Now you have the opportunity to bring this iconic style to your own Triumph Bobber – with the exclusive RxV rear kit, which is an absolute eye-catcher, especially in combination with the matching RxV headlight fairing.
Turn your Triumph Bobber into a custom bike!The 3D-printed RxV rear end takes your Triumph Bobber to a whole new level. With the integrated LED rear light, perfectly incorporated into the minimalist design of the rear, your Bobber becomes a unique custom bike that is guaranteed to turn heads on the road.
High-quality materials for the best quality:
3D printing technology: The rear consists of precisely manufactured plastic parts that have been produced using the latest 3D printing technology, making it robust and durable.
Steel construction: The steel receiver allows for easy mounting on the original mounting points of your bobber's seat. In addition, the steel seat base plate provides stability and allows you to customize the seat.
Seat cushion and cover: The rear end is delivered without a seat cushion and cover so that you can customize the seat design to your own preferences. Visit your favorite saddler or ask us about our professional cover-fitting service.
Paintwork: The rear consists of three 3D printed plastic parts. You can order these either in RAW (unpainted) or in black gloss/matt. The black parts are painted to customer order and have an approximate delivery time of 4-8 weeks.
LED rear light – stylish and functional:The integrated LED rear light (incl. e-number) ensures clear visibility and perfectly matches the clean, open design of the rear. Please note that the position of the rear light in the EU does not officially meet the prescribed standard, as it is more than 30 cm from the rear wheel. In practice, however, this is not a problem because the rear light is highly visible due to the open design of the bobber.
Installation instructions:
Turn signals: For installing the turn signals, we recommend our Frame Blinker Holder or Frame Flasher. Both products can be found in the accessories.
License plate: We recommend a side license plate holder for the perfect custom look. Suitable models can also be found in the accessories.
Fender: For the perfect custom look, we recommend mounting a short fender or no fender at all. You can find two different short fenders among our accessory products.
Wiring: To be able to easily plug the rear light and new turn signals into the wiring harness plug of your bobber, we recommend that you also order the cable set.
Demonstrator / used variant:
We have the kit in black gloss with a slight yellow accent on the inside as a demonstrator part (including pads & seat cover) as in the photos for sale at a special price. The part was mounted on a display motorbike for a time. Condition is as good as new.
Oil filler plug - Custom Cap Flat
CB12687
/ RS10
From
€38.95*
Oil filler plug made of high-pressure cast aluminum.
The screw can be easily replaced with the original one.
The matching design for the Custom Cap Flat fuel filler cap.
Rear Fender Kit - Bobber - Flashed
CB12620.1
/ RS10
€799.00*
Colour:
Glossy Black
A shorter fender? The flashed fender kit from KRT Framework for the Triumph Bobber perfectly combines functionality and aesthetics. A clean fender without a central bead, designed significantly shorter than the original.Unlike the original fender and most other accessory fenders, the flashed fender still has a flare on the side, which underpins a classic chopper handle.
Indicators and rear lights are also reduced to a minimum and integrated into the fender struts. Even if you don't notice them at first glance, you can't miss them in action thanks to modern SMD LED technology. Equipped with an E-mark and arranged in such a way that they meet all StVo requirements, you can mount this fender kit in the reassuring knowledge that you are 100% legal on the road.
The kit is manufactured entirely in Germany.
Materials used and production method:
The fenders are made from the finest carbon. The material is placed by hand in a negative mold and then baked under vacuum and heat. This process makes it possible to produce lightweight and extremely accurately fitting parts. Only high-quality components are used for the materials, including fibers and resins, which are also used for the production of rotor blades.
The mounting system, which is connected to the mudguard, is made of laser-cut and folded aluminum. After machining, it is powder-coated black. These brackets are designed so that you can adjust the height of the fender in relation to the tire. The fender struts themselves are made of steel to make them visually slim yet stable. A slotted hole is incorporated in the lower mounting for height adjustment.
The turn signal cable exits from the bottom of the fender struts and can be routed directly behind the swingarm tube to enable inconspicuous routing.
Our friend Marvin (KRT) carries out all the work steps himself, from mold construction to carbon production and metalwork. If you are interested in the production of the prototypes and parts, take a look at the videos below the product description.
Versions and their finishes:
The Flashed fender is available in a visible carbon version, for which we use a carbon canvas fabric that is also used by Ducati and Porsche. On request, owners of a Bobber TFC can obtain a special version in which we use a twill weave. The matt finish visually matches the original carbon parts of the TFC. However, as the TFC is limited, this part is only produced on request.
We also offer two ready-painted versions: one in gloss black and one in matt black. Both match the original colors. For those looking for individual color options, an unpainted RAW version is available. This is primed and optimally prepared for a custom paint job by your painter.
The wiring:
For many, wiring is a vexing issue and probably the most time-consuming element of converting to the mudguard kit. Without high-quality electronic tools, the whole thing can hardly be carried out professionally. But we also have a plug & play solution for this in our range.
The fender struts with integrated lighting are already pre-wired and equipped with a high-quality 4-pin plug on each side. This plug is molded directly onto the end of the cable and sealed watertight thanks to the IP66 protection class. This is particularly important in the swingarm area, where the plug can get a lot of moisture.
We have assembled a pre-wired cable harness for the rear for this plug. With this, the mudguard can be easily fitted plug & play. A little tip: If you order a KRT license plate holder at the same time, the license plate light will be supplied with the matching plug for our wiring harness (please contact us personally after ordering). This means you don't have to bother with individual cables during the conversion, but can plug our cable set directly into the original 8-pin plug of the original wiring harness.
Please note that the wiring harness must be purchased separately. You can find the wiring harness under accessories in this product description.
However, if you prefer to take care of the wiring yourself, we have deliberately left the cables of the fender struts long enough so that you can remove the plugs and connect the electrics yourself.
Accessories and combinable products:
To get the perfect overall look, your bobber naturally needs a side license plate holder. There are several options to choose from (all of them fit in our range). However, we would recommend the one from KRT in order to have a complete package from KRT (can be found under accessories in this product description).
Variants from €699.00*
License plate holder kit side - Scrambler 1200
CB12593
/ RS10
The side license plate holder KIT for all Triumph Scrambler 1200 models contains everything you need to convert your Scrambler 1200 to a side license plate holder together with the original rear mudguard with 3-1 rear light / indicators.ATTENTION, the 3-1 indicators are not included, you can order these below the product description (with a 10% discount).
Contents of the kit: - Side license plate holder - vario - Triumph rear light replacement kit Scrambler 1200 (Attention the plate with the T logo is delivered in aluminum silver NOT in black) - Blinker adapter LC (necessary to mount accessory indicators on the tail light replacement kit)
Accessory article:- For easy connection of the 3-1 indicators we recommend to order the cable set (see below the description).- To mount the license plate as inconspicuously as possible, we recommend ordering a license plate screw set (see below the description).- If you want it to be 100% legal, we recommend ordering a reflector (see below the description).
Notes on the side license plate holder:The Classicbike-Raisch Vario side license plate holder for the Triumph Scrambler 1200 models has a well thought-out mounting system, which makes it possible for the license plate holder to look good and not protrude too far outwards on the one hand and to be legal and registrable on the other.
The design of the holder is deliberately kept as minimalist as possible, because a side license plate holder should simply be as inconspicuous as possible.
Various mounting holes make it possible to position the license plate far outwards. This then enables registration with your trusted TÜV inspector.Side license plate holders do not require an ABE or parts certificate. For registration, they only need to comply with the StVO guidelines, which is the case with our Vario holder if the license plate is mounted in the outermost position. After registration, the license plate can then be moved further inwards for a more attractive appearance. The product images illustrate the adjustment range of the license plate. Please clarify in advance with your TÜV inspector whether he will register the license plate holder (if necessary, we can supply a sample registration).
The license plate carrier plate has a dimension of: Height = 100mm / Width = 155mm - The dimension is small enough to accommodate all motorcycle license plates in the world.Scope of delivery side license plate holder: - Side license plate holder made of aluminum (Made in Germany)- Mounting material + cable for the license plate light - LED license plate light- Detailed step-by-step installation instructions
From
€289.95*
High Mount Mudguard - Scrambler 1200
CB11823.1M
/ RS10
From
€239.00*
This 2mm thick top-mounted aluminium mudguard in Scrambler style, from the Triumph original accessories, is mounted underneath the original triple clamp of the Scrambler.
This is the only way to get the real off-road Scrambler look! Because an off-road motorbike has the front mudguard sitting far above the front wheel!
Everything needed for mounting is included in the scope of delivery.
The mudguard is available in brushed silver (like the other aluminium add-on parts on the Scrambler 1200) or powder-coated black.
High Mount Mudguard - Street Scrambler 900
CB12525
/ RS10
€269.00*
This Jet Black coloured top mudguard in Scrambler style, from the Triumph original accessories, is mounted below the original triple clamp of the Scrambler. A short, small mudguard is also included, which serves as a splash guard (this does not have to be fitted, however, if you are concerned about the appearance).Suitable for Scrambler 900 and Street Scrambler from VIN 914448 onwards.
This gives you the real off-road Scrambler look! Because an off-road motorbike has the front mudguard sitting far above the front wheel!
Everything needed for mounting is included in the delivery.
We can also supply the mudguard in other Triumph original colours on request.
Roswell Öl Screw
CB11973M
/ RS10
From
€38.95*
Oil filler plug made of high pressure cast aluminium.
The screw can easily be exchanged for the original one. Can be tightened by hand or with an Allen key.Black powder coated and then hand polished to get the nice contrast between black and polished.
Roswell Öl Screw
CB11737.2M
/ RS10
From
€38.95*
Oil filler plug made of high pressure cast aluminium.
The screw can easily be exchanged for the original one. Can be tightened by hand or with an Allen key.Black powder coated and then hand polished to get the nice contrast between black and polished.
Short Front Mudguard Bobber & Speedmaster
CB11546M
/ RS10
From
€269.00*
Short steel front fender in glossy black lacquer.If you want a more radical look and the original long fender is a thorn in your side, you should use this short original Triumph fender. Supplied complete with bracket.
Radiator Guard - Billet
CB11518M
/ RS10
From
€174.95*
Protective grille for the water cooler in UK Jack design.This grille makes the not exactly beautiful and above all not popular water cooler on our beloved Classic Twins clearly more handsome!Unlike most providers, this is not a simple cover that is simply unscrewed. The entire original grille will be replaced by the UK Jack grille (mounting material included). Made of high quality aluminum & steel in black powder coated.The cooler still gets as much air as with the ori grille, is just as well protected, but looks much nicer!Translated with www.DeepL.com/Translator
New
Cotado Frame Loop Heck Kit
CB12817
/ RS20
€999.95*
Complete rear arch kit including seat for Triumph Bonneville T100 / T120 and Street / Speed Twin 900 - Street / Scrambler 900.
Do you want to give your Triumph a crisp, short rear end that screams pure custom look? Then the Cortado rear kit is perfect for you! This complete set gives you everything you need to realize your dream of a clean rear end yourself – and you don't even need a professional workshop or welding equipment.
What's included and what makes it special?
The Cortado rear kit is the perfect solution for anyone who dreams of the classic cut-off rear frame with a stylish arch. Whether you have a Triumph Bonneville T100/T120, Street Twin, Speed Twin 900 or Scrambler 900, this set is the perfect fit and looks damn good. Included are:
A rear arch that is not welded but bolted on – it couldn't be easier or less stressful.
Plug & play mudguards and a seat that are perfectly matched to your bike.
Everything you need for installation, including a template, paint, a cable set and more.
You don't have to be a full-time mechanic to take your bike to a new level with this kit. Thanks to the included template, you can cut the rear frame precisely. And we've even thought of the black paint can, so that the cut is neatly sealed. There's no need to worry about the bench either: simply attach it like the original with the key lock – done!
DIY with a professional feel – but relaxed
Of course, a kit can never quite match the perfection of a tailor-made professional conversion, but with the Cortado Kit you get an absolutely top-quality result – and at a super fair price. The best thing: detailed instructions and a YouTube video show you step by step how to do it. Hobby mechanics, take note – now it's time to get to work!
Don't forget the legalities
Important: A conversion like this must be approved by the TÜV (Technical Inspection Authority) so that you are legally on the road. It's best to clarify the conversion with your TÜV inspector or a workshop beforehand – just to be on the safe side.
Kit contents:
Bolt-on rear frame arch
Comfortable bench seat
Black aluminum mudguard
Eldorado aluminum rear light with LED license plate illumination and adjustable angle
License plate holder
Precise template for cutting the rear frame
Paint can for sealing
Cable set for plug & play connection of rear light and indicators
Classicbike-Raisch tips for your perfect rear:
Get small accessory LED indicators to go with it, such as the Motone Pico, Motogadget Pin, Rizoma Club or Kellermann Bullet – they'll complete the look.
For a 100% legal rear end, don't forget a reflector on the license plate!
With our license plate screw set, the license plate can be mounted cleanly and securely.
Conclusion:With the Cortado rear kit, you can easily turn your Triumph into your own personal custom bike. No welding, no major hurdles – just you, your bike and a little craftsmanship. Treat yourself to the clean look and take your machine to the next level!
Ripped Ritzelcover LC
CB12060.1M
/ RS20
From
€149.95*
Motone sprocket cover in ripped design.
Made of die-cast aluminum. Matching design to our well-known side covers, engine covers and other small accessories covers that are also available from us in the Ripeed design.
The assembly of the cover is very simple and done in a few minutes.
Rizoma Licensholder Fox Speed Twin
CB11896
/ RS20
€190.00*
The Rizoma license plate holder "FOX" with license plate illumination has been the absolute classic in the motorcycle industry for years and convinces without many words by its sophisticated adjustment system and perfectly matured construction. The original aluminium mudguard of the Triumph Speed Twin is preserved. The original very long license plate holder is replaced by the short Rizoma holder. A removable reflector is included in the delivery.
The rear looks perfect in combination with small Rizoma turn signals, which can be mounted on the original mounting, best together with our turn signal adapters.
If the Rizoma Fox tail is too expensive, we recommend our simple but minimalistic Raisch holder (see similar products).
Side cover - Speed Twin 1200
CB12796
/ RS50
From
€509.00*
Plug & Play fiberglass side covers for your Triumph Speed Twin 1200
Give your Speed Twin a clean side line with these custom-fit fiberglass side covers. The beautifully shaped covers blend harmoniously into the design and match the injection molding perfectly for a consistent look that appears to be cast from a single mold.
The side covers can be exchanged for the original covers in just two steps. Both the accessory and original covers are simply inserted into rubbers, which makes the change particularly uncomplicated.
Available variants:
Raw (unpainted)
Painted in gloss or matt black
The kit is manufactured to a very high standard by a small-batch producer and is often only produced when an order is placed by a customer.
We try to keep all variants in stock, but this is not always possible, which is why a short delivery time must be expected from time to time.
Side cover - Triumph Scrambler
CB12797
/ RS50
From
€299.00*
Plug & Play fiberglass side covers for your Triumph Scrambler 1200 / Street Scrambler / Scrambler 900
Give your Scrambler a clean side line (on the left side) with these custom-fit fiberglass side covers.The beautifully shaped covers fit perfectly into the side line of your scrambler and match the injection molding perfectly – for a consistent look that appears to be cast from a single mold.
The side cover can be exchanged for the original cover in just two simple steps. Both the accessory and original covers are simply inserted into rubbers, which makes the exchange particularly uncomplicated.
Available variants:
Raw (unpainted)
Painted in gloss or matte black
The side covers are manufactured to a high standard by a small-batch manufacturer and are often only produced to customer order. We try to have all variants in stock, but this is not always possible, which is why a longer delivery time must be expected.
Crash bar black coating
CB12479
/ RS50
€65.00*
True to the motto black is beautiful, you can send us all the metal parts of your motorcycle so that we coat them black.You do not like the silver of your engine guards crash bars? Then send them to us and we coat them in black.
We will then coat the part in black satin (RAL9005).
The processing time is approximately 2 - 4 weeks.
Attention! We offer here only the service of the coating. The original part must be delivered to us by the customer.
Front Mudguard Powder coating black
CB12197
/ RS50
€65.00*
You have an aluminum fender and you don't like the silver anymore? Then send it to us and get it back in black.
The part will be powder coated by us in black satin (RAL9005).
The processing time is about 2-3 weeks.
Attention! we only offer the service of coating here. The original part must be delivered to us by the customer.
Exhaust Heat Shield Powder coating black
CB12198
/ RS50
€60.00*
You would like the original rear exhaust heat shield of your Scrambler in black?
Then just send it to us and we will coat it black satin (RAL9005) powder.
The processing time is about 2-3 weeks.
Attention! We offer here only the service of coating. The original part must be delivered to us by the customer.
Rear Mudguard Powder coating black
CB12199
/ RS50
€75.00*
You have an aluminum fender on your machine and you don't like the silver anymore? Then send it to us and get it back in black.
The part will be powder coated by us in black satin (RAL9005).
The processing time is about 2-3 weeks.
Attention! we only offer the service of coating here. The original part must be delivered to us by the customer.
Sump Guard Powder coating black
CB12200
/ RS50
€70.00*
True to the motto black is beautiful, you can send us all the metal parts of your motorcycle so that we coat them black.You do not like the silver of the original engine guard on your Scrambler 1200? Then send it to us and we will take care of the coating.
The part is then coated by us in black satin (RAL9005).
The processing time is about 2-3 weeks.
Attention! We only offer the service of coating here. The original part must be delivered to us by the customer.
Tank Belt Powder coating black
CB12201
/ RS50
€50.00*
Everything should be black? Then send us your original aluminum tank belt including the buckle and we will take care of the coating.
The parts will then be coated black satin (RAL9005) powder.
The processing time is about 2-3 weeks.
Attention! We offer here only the service of coating. The original part must be delivered to us by the customer.
Side Cover Badges Scrambler Powder coating black
CB12203
/ RS50
€55.00*
The two aluminum plates on the left side cover of your Scrambler 1200 are too conspicuous.
Then just send them to us and we will coat it black satin (RAL9005) powder.
The processing time is about 2-3 weeks.
Attention! we offer here only the service of coating. The original part must be delivered to us by the customer.
Injection Covers Powder coating black
CB12204
/ RS50
€35.00*
You would like to have the original, silver Injection plates of your Motrrades in black?
Then just send it to us and we will coat it black satin (RAL9005) powder.
The processing time is about 2-3 weeks.
Attention! We offer here only the service of coating. The original part must be delivered to us by the customer.
Headlight Brackets Powder coating black
CB12206
/ RS50
€65.00*
You would like to have the original Headlight holders of your bike in black?
Then just send them to us and we will coat it black satin (RAL9005) powder.
The processing time is about 2-3 weeks.
Attention! We offer here only the service of coating. The original part must be delivered to us by the customer.
Handguards Scrambler 1200 Powder coating black
CB12207
/ RS50
€70.00*
You want to have the metal struts of your Scrambler 1200 like in black?
Then just send them to us and we will coat it black satin (RAL9005) powder.
The processing time is about 2-3 weeks.
Attention! We offer here only the service of coating. The original part must be delivered to us by the customer.
Side Stand black Powder coating
CB12208
/ RS50
€60.00*
Black Black Black! Not all side stands are black from the factory. If you make all the parts on the bike black, the stand also stands out negatively in silver. We can also coat it black for you.
For this simply send us your side stand and we will coat this black satin (RAL9005) powder.
The processing time is about 2-3 weeks.
Attention! We offer here only the service of coating. The original part must be delivered to us by the customer.
Footrests black Powder coating
CB12211
/ RS50
€60.00*
You like the original Rasten your mr machine very well, because they are actually pretty cool (such as the Scrambler 1200), but they do not like you in silver?
Then just send them to us and we will powder coat it black satin (RAL9005).
The price is for ONE PAIR of rests. Please remove all attachments like rubbers or similar from the footrests and do NOT send them to us! Please note that the coating in the area where the foot rests will wear off over time.
The processing time is approximately 2-3 weeks.
Attention! we offer here only the service of the coating. The original part must be delivered to us by the customer.
Coating injection strips cover black
CB12275
/ RS50
€35.00*
They like the original injector covers very much, but you would like them in black?
Then just send them to us and we will powder coat it black satin (RAL9005).
The processing time is about 3-4 weeks.
Attention! We offer here only the service of coating. The original part must be delivered to us by the customer.
Exhaust catalytic converter cover black coating
CB12312
/ RS50
€60.00*
You would like to have the original catalytic converter heat shield of your Scrambler in black?
Then just send it to us and we will powder coat it black satin (RAL9005).
The processing time is about 2 - 4 weeks.
Attention! We offer here only the service of coating. The original part must be delivered to us by the customer.
Crash bar black coating
CB12425
/ RS50
€85.00*
True to the motto black is beautiful, you can send us all the metal parts of your motorcycle so that we coat them black.You do not like the silver of your engine guards crash bars? Then send them to us and we coat them in black.
We will then coat the part in black satin (RAL9005).
The processing time is approximately 2 - 4 weeks.
Attention! We offer here only the service of the coating. The original part must be delivered to us by the customer.
Exhaust cat cover black coating
CB12426
/ RS50
€60.00*
True to the motto black is beautiful, you can send us all the metal parts of your motorcycle, so that we coat them black.You would like to have your original cat screen in black? then just send it to us and we take care of everything!
The part will then be coated by us in black satin (RAL9005).
The processing time is about 2 - 4 weeks.
Attention! We offer here only the service of the coating. The original part must be delivered to us by the customer.
Radiator grille black coating
CB12320
/ RS52
€60.00*
True to the motto black is beautiful, you can send us all the metal parts of your motorcycle so that we coat them black for you.You do not like the silver of the Triumph accessories radiator grille on your Scrambler 1200? Then send it to us and we will take care of the coating.
The part will then be sandblasted by us and coated in black satin (RAL9005).
The processing time is about 3 - 4 weeks.
Attention! We offer here only the service of coating. The original part must be delivered to us by the customer.
Motone Chain Guard Tanto LC
CB11921M
/ RS200
From
€55.95*
A very nice and slim chain guard, made of high quality stainless steel.
The chain guard can be easily replaced with the original one in a few minutes.
Engine cover screws stainless steel / LC
CB11986M
/ RS500
From
€29.90*
Engine cover screws stainless steel hexagon socket in untreated or black coated heads for all water cooled Triumph models.Replaces the rather simple looking hexagon socket head screws.For the two big engine covers left and right and for the cover of the sprocket cover. Simply replace them with the originals and tighten them with 9 Nm or hand-tight. Damage due to weather influences is impossible with these screws.To the black screws:All included screws are made of stainless steel A2-70 The black screws are powder coated in a beautiful black matt. Optically great, if the screws should not attract attention. No flaking of the color! Much higher quality than the black screws from Triumph.They are just galvanized and look like raw steel screws.The screws are neatly packed in bags for the respective engine cover. The exchange is therefore very easy. One screw after the other is replaced. Therefore no new gaskets are needed.The screw kit includes all screws for the motor covers + sprocket cover + water pump, if available!
Engine cover screws stainless steel / LC / Gold
CB11987
/ RS500
€69.95*
Engine cover screws stainless steel hexagon socket with gold plated screws for all water cooled Triumph models.True to the motto "the world goes down in a noble way" the screws are covered with a thin layer of real gold (to guarantee a really beautiful and constant gold tone).Optically the screws set a really chic accent. Fits especially well to the models with gold fork.Replaces the rather simple looking hexagon head screws.For the two big motor covers left and right and for the cover of the sprocket cover. Simply replace them with the originals and tighten them with 9 Nm or hand-tight. Damage due to weather influences is impossible with these screws.The screws are neatly packed in bags for the respective engine cover. So the exchange is very easy. One screw after the other is exchanged. Therefore no new gaskets are needed.
Sprocket cover emblem - Raisch
CB12807
/ RS599
€19.95*
Insert plate for the sprocket cover of all Triumph Bobber & Speedmaster 1200 models with a delicately milled Raisch logo. The factory version of the models features the silver Mesch grid in the sprocket cover. Our Raisch emblem is simply clamped in between (to do this, the sprocket cover has to be removed and screwed on from behind, it's very easy and can be done in 2-3 minutes).With the emblem, the silver surface in the sprocket cover then disappears.The Raisch emblem is milled from a single piece of aluminum, black anodized and then the Raisch logo is milled with a filigree milling head.
Injection cover Triumph
CB10840M
/ RS599
€59.00*
Original cover for the injection system from Triumph as a replacement for the original part. The noble Triumph emblem enhances the appearance of the already beautiful injection system a little bit.
Engine cover badge Triumph
CB10783M
/ RS599
From
€59.00*
Engine cover emblems for clutch & generator cover in black, chrome and matt brushed. The cast aluminium emblem discreetly underlines the design of your machine. For mounting on your Triumph machine instead of the standard part.Fits all water-cooled Triumph models.
Engine cover badge Triumph ripped
CB10784M
/ RS599
From
€59.00*
Engine cover emblems in ripped design as a replacement for the original. The cast aluminium emblem discreetly underlines the design of your machine. Available in chrome, black and silver matt.Fits all water-cooled Triumph models.
New
Relocation kit Horn for Bobber
CB11419
/ RS600
From
€19.90*
With this kit, the original horn, which sits in front of the radiator is placed behind the radiator, to get a clean front.
Slim Tail Tidy
CB12795
/ RS600
From
€489.00*
Short rear fender kit for your Triumph Bonneville / Street Twin / Speed Twin 900 / Street Scrambler / Scrambler 900
Want to give your Triumph a modern, clean look? Then this short rear kit is perfect for you! With everything you need (except small turn signals – you can order those separately), you can make your rear end sleek and stylish. The complete kit makes installation quick and easy, so you can transform your machine into a real eye-catcher in no time.
Included in the scope of delivery:
• Fiberglass fender: Stylish, short look with a sturdy design
• Aluminum underframe: Ensures stability and a tight fit
• Aluminum license plate holder: Adjustable turn signal holders for flexible adjustments
Cable set: For direct connection to the original wiring harness of your Triumph
LED rear light and license plate light: Modern, bright and energy-saving
The straight rear fender adds a distinctly radical touch and gives your motorcycle an eye-catching, unique style. Of course, the kit is completely legal and street-legal. For 100% street legal use, we recommend our additional reflector – just to be on the safe side.The kit is manufactured to a very high standard by a small-batch producer and often only produced to customer order. We try to have all variants in stock, but this is not always possible, which is why a little delivery time sometimes has to be expected.
Side cover leather bag - Scrambler 1200
CB12671M
/ RS600
From
€229.95*
Suede side bag suitable for all Scrambler 1200 models with bottom-mounted exhaust. If you move the exhaust of your Scrambler downwards, the original side bag looks rather unsightly. This handmade, 3mm thick leather bag from Unit Garage in Italy closes this unsightly gap and makes the Scrambler look good again.
The small bag is also a very practical companion. The bag has 3 elastic bands inside the lid, under which you can quickly stow things (such as a wrench or sunglasses). There is also a pocket hidden under the zipper where you can stow the essentials for a short trip.
The bag is waterproof.
Rear fender Shorty - Bobber
CB12621.3
/ RS600
€419.00*
Colour:
Carbon
Shorty mudguard for Triumph Bobber. The classic among the short fenders for the Triumph Bobber. As the sides of this fender enclose the tire, it has a more classic look, blends in perfectly with the original vehicle line and underlines a classic chopper style. A clear view of the rear wheel combined with a harmonious overall look. If you are out and about in the rain, it will of course only protect you from splash water to a limited extent. However, it does protect the shock absorber, airbox and various cables and relays, which are positioned directly in front of the rear wheel, from dirt, grime and stone chips. It is therefore more suitable for those of you who want to give your bobber a more minimalist line without taking away its classic look. Because without a mudguard, it usually looks a bit strange.
The bracket system allows individual positioning of the mudguard: The distance between the fender and the tire is adjustable, so you can adjust this precisely to the chain setting. Even when using different tire types, it is possible to adjust the height of the mudguard optimally. Note, however, that a tire expands at high speeds. A distance of at least 7 mm should therefore be set. For an even more minimalist look, the mounting point for the original chain guard can be removed. You can remove this if you want to fit a short chain guard. Like all KRT parts, this mudguard is also manufactured by us. From the prototype to the mold production to the finished carbon part, all work steps are carried out in-house. The mudguards are manufactured using the RTM process, whereby the carbon fiber is impregnated with resin under vacuum and heat. This process enables extremely light and precisely fitting components. The fibers and resins used for production meet current aviation standards and are also used in the construction of rotor blades. Versions and their surfaces:
The mudguard is available in a visible carbon version, for which we use a carbon canvas fabric that is also used by Ducati and Porsche. On request, owners of a Bobber TFC can obtain a special version in which we use a twill weave. The matt finish visually matches the original carbon parts of the TFC. However, as the TFC is limited, this part is only produced on request.
We also offer two ready-painted versions: one in gloss black and one in matt black. Both match the original colors. For those looking for individual color options, an unpainted RAW version is available. This is primed and optimally prepared for an individual paint job by your painter.
Matching accessories:
To build a complete rear kit around the short mudguard, other accessories such as license plate holder, indicators / rear light, possibly a short chain guard are required. You can find our product recommendations for the short mudguard under the accessories in this product description.
Variants from €289.00*
%
Öl Schraube - Matt Silber
CB12822
/ RS600
€17.90*
€24.90*
(28.11% saved)
Alumiunium Öl Einfüllschraube in matt Chrom.
Short aluminium mudguard - Speed Twin E5
CB12521.1M
/ RS600
From
€159.95*
Heavy duty aluminium mudguard suitable for Speed Twin 1200 Euro 5 models in the short version.
The mudguard is made of solid aluminium (stamped), brushed to get the nice surface and then anodised.
Can be exchanged plug & play against the original one. The original mudguard brackets remain intact.
If you want a wing with more filigree brackets, we recommend our Raisch short wing kit (see similar articles in this description).
Battery box belt
CB12364M
/ RS600
From
€74.95*
This fancy leather belt replaces the original battery box belt on your Bobber or Speedmaster.
Is simply plug & play exchanged.
Especially the small brass applications make the belt look very high quality.
Injector plates - Zephyr
CB12317M
/ RS600
From
€74.95*
A pair of die-cast aluminum injector plates in black.
These plates replace the original silver plates. The exchange is done in 1-2 minutes.
Tamarit Edelstahl Kettenschutz LC
CB12138
/ RS600
€99.00*
Model:
Bonneville T100/T120 & Street Modelle
Tamarit Motorcycles Kettenschutz für die Wassergekühlten Triumph Modern Classic Modelle.
Alle Tamarit Kettenschütze sind aus Edelstahl gefertigt. Damit ist eine sehr schöne silberne Oberfläche sowie Rostschutz gegeben.Die Cover sorgen durch ihr geripptes Design für einen sportlich eleganten Look.
Der Anbau ist sehr einfach und in kurzer Zeit erledigt. Originaler Kettenschutz ab und den neuen genauso wieder anbauen.
Auf Wunsch können wir die Kettenschütze auch in schwarz Pulver beschichtet lifern.
Triumph Tail light replacement for 3-1 indicator
CB12101.3M
/ RS600
This Triumph taillight replacement for the for various Triumph models allows to dismantle the original taillight and 3-1 turn signals (turn signals with integrated taillight to install).
To get a nice solution (as on the product images), the Raisch turn signal adapter is needed (you can order below the description simply in the set to. This then allows all accessories 3-1 turn signals with M8 thread to mount.In addition, we also recommend the cable set for easier wiring to order (Attention for the Speed Twin Euro 5 models there is no cable set, these models must be wired manually).
Matching turn signals to the set you can order with 10% discount, below the description in the set. Our recommendation for this set are the turn signals of the brand Rizoma, which fit perfectly.
Tip Scrambler / Speed Twin 1200: To get a really cool and clean tail on these models, we recommend a short license plate holder to order (see accessories below the description).
The aluminum plate with the Triumph emblem is supplied in silver.
From
€65.00*
Fork Cover The Capos
CB12297M
/ RS600
From
€149.95*
Motone The Capos fork head cover made of titanium in star design.
The heads are simply replaced 1 to 1 with the original ones. The fork does not have to be removed from the bike.
Looks especially good in combination with the matching steering head nut from our range (see accessories in this description).
Start license plate for SLC holder
CB12049M
/ RS600
From
€55.00*
SW-Motech start number plate suitable for all Sw-Motech Legend Gear SLC bag holders (matching holders see ZUbehörartikel in this description).
The plate is made of brushed aluminum and looks very high quality. On request, we can also coat this black powder for an additional charge.
The sign is very easy, just like the Legend Gear bags with the quick release system clicked into SLC holder.
Perfectly suited for all who have installed the SLC holder and do not always want to have the bag on the bike but do not want to look at the holder.
Break lever black coating
CB12039
/ RS600
€45.00*
Black is beautiful! True to this motto, we offer you the possibility of virtually all metal attachments of your machine to send to us and we powder coat them to you in black satin and send them back to you.
Simply send us the dismantled brake lever and we will take care of everything else.
Delivery time is about 2-3 weeks.
Attention! We offer here only the service of coating. The original part must be delivered to us by the customer.
Rizoma Öl Einfüllschraube Triumph
CB11918M
/ RS600
From
€50.50*
Öl Einfüllschraube von Rizoma, für alle Triumph Modelle.
Für alle die es besonders Edel mögen, ist die Schraube von Rizoma genau das richtige.Denn alle Rizoma Produkte werden aus sehr hochwertigem Aluminium hergestellt und haben eine sehr schöne, eloxierte Oberfläche.
Die Schraube wird ganz einfach gehen die originale ausgetauscht.
Öl Einfüllschraube Crown
CB11834
/ RS600
€24.95*
Hochwertige, CNC gefräste Alu Schraube in tief schwarz eloxiert.
Einfach gegen die originale Schraube austauschen.
LED taillight + turn signal conversion Scram 1200
CB11833
/ RS600
€126.00*
This Triumph LED rear light allows you to mount the Scrambler 1200 indicators on the rear light instead of the original license plate holder. In addition the original taillight is replaced by a nice small LED taillight.
You can either continue to use the original turn signals (which we do not recommend, because they look too big compared to the LED tail light) or the Triumph LED turn signals (see accessories in this description).
Street Scrambler number plate.
CB11565
/ RS600
€49.00*
A scrambler simply needs a number plate. With this board you can give the Steet Scram a real competition look. Just stick your own or your favourite start number on it and that's it!
Ignition lock housing Bobber CNC
CB11420
/ RS600
€89.90*
CNC machined housing for the original ignition lock of the Bobber. Includes relocation kit to the left side.
The ribbed design of the housing nestles perfectly into the look of the cooling fins of the motorcycle.
By relocating it to the left side, the ignition lock becomes much more inconspicuous, as it slides further into the center of the motorcycle and fits better between the other parts on the left side of the motorcycle. It simply doesn't catch the eye anymore in that spot. If you don't know where the ignition lock is, you can hardly find it, as it should be.
Universal license plate holder
CB11294M
/ RS600
From
€29.95*
Universal identification holder for mudguards.
The license plate is universal for many mudguards. It is screwed from the inside to the fender (see photo)
Ripped Side Cover painted LC
CB12016M
/ RS600
From
€234.95*
A pair of Motone high-quality ABS plastic side covers in ripped style with a shiny or matt black finish. The three slotted ribs give the side lids a really classic sporty look.A nice little side effect is that the bike also gets a little more air.The lids are painted ready for mounting. A fine, silver mesh aluminium grid is glued in behind the slots so that you can't just look through the ribs.
Turn your water-cooled Triumph Modern Classic motorcycle from 2016 into an eye-catcher with our body parts!
Whether it's a Bobber, Bonneville, Speed Twin, Scrambler, Thruxton, Street Twin, Street Scrambler, Speed 400 or Scrambler 400 X – we offer everything you need to make your bike unique. From stylish covers and custom emblems to complete rear conversion kits, you'll find the right mudguards, side panels and licence plate holders for central or side mounting here. Get the perfect body upgrade and transform your Triumph into a real custom bike!